• Reference RSS Feed

    Avance del artículo

    How much high frequency is lost over long distances? ...
    Avance del artículo

    In the loudness contours reference, we learned that the frequency response of the human ear is not flat and it also varies ...
    Avance del artículo

    The equal loudness contours (often referred to as Fletcher & Munson contours for reason explained below) represent the level that different frequencies need to have in order to be perceived by a listener ...
    Avance del artículo

    The different types of directional patterns in microphones are a common source of inaccurate graphical representations as well as numerical data that are not entirely correct or complete. In this reference we include a table of complete parameters as well as polar curves. ...
    Avance del artículo

    The following table shows the resulting damping factor, signal loss, attenuation and impedance for different loudspeaker ...
    Avance del artículo

    Maximum speaker cable lengths for :


    • Low impedance (2, 4, 8 and 16 ohm)
      • Quality
      • 3 dB loss, which could be an alternative to a line transformer system

    • High impedance (systems with line transformer)
      • 70V
      • 100V

    ...
    Avance del artículo

    In this article we'll explain impedance calculations as simply as possible, as well as describe the different types of connection. ...
    Avance del artículo

    The illustrations below show the connection between balanced and un-balanced outputs on different connector types (XLR / Cannon, 14", phono/RCA/cinch) to balanced inputs on XLR and 1/4" connectors. ...
    Avance del artículo

    There are many types of sound sources that do not require subwoofer reinforcement since they lack low frequency content. For instance, most signals captured by microphones such as voices and instruments in general, except those that do have low frequency content, like double ...
    Avance del artículo

    This article will explain loop-though connections and "y-cables" for analog audio signals. ...
    Avance del artículo


    Tables for conversion from Q to B/W (bandwidth) for DSP bell-type EQ. ...
    Avance del artículo

    The spectra of pink and white noise are often a source of confusion. The difficulty arises from the fact that the spectra of these types of noise (or rather, their graphical representation) will change depending on the type of analyzer that ...
    Avance del artículo

    In general, two-channel power amplifiers for professional use default to stereo mode. That is, each amplifier channel receives a signal from its input connector and its volume is controlled by that channel's volume control. So, really, although the name of that default mode is 'stereo', it is more of a two-channel mode, since those two channels do not necessarily have to be right and left. For example, they could be two separate channels for the stage monitors of different musicians. Or the high and midrange bands of a multi-amp system ...
    Publicado el 16 ene 2019 15:19
    Avance del artículo

    Pin asignments for an assortment of connectors: XLR, 1/4" (jack), 1/8" (minijack), SpeakON, DB25, DMX ...

    ...
    Avance del artículo

    Octaves, thirds of octaves and decades are divisions of the spectrum used in audio, since they work in the same way as the ear, increasing their width in Hertz as frequency increases, and decreasing it when frequency decreases. They are used for the definition of the width of filters, as well as for the spectral analysis. ...
    Avance del artículo

    For cost and space saving reasons, some devices often use connectors that integrate both an input and an output, typically on a female 1/4" connector. This type of arrangement ...
    Avance del artículo

    Although it not specific to sound, we include this document with some basic electricity formulas. They can be found in any electricity textbook, but we have added them to the DoPA Library for reference ...

  • Ad

  • News

    L-Acoustics L-ISA Processor II extends immersive processing to more productions

    L-Acoustics’s unveiling of L-ISA Immersive Hyperreal Sound technology in 2016 extended spatial processing to a wider range of productions and venues, L-Acoustics now rolls out the next generation of its 3D audio processing... Read more

    Alcons Audio intriduces QRP20 Pro-Ribbon point source column

    Dutch manufacturer Alcons Audio has launched the QRP20, a 2-way column array system with high-Q directivity for increased projection control to be used as vertical sound system, for both permanent... Read more
    Etiquetas: alcons 

    Audio-Technica BP28 and BP28L line+gradient large diaphragm condenser microphones

    Audio-Technica is launching its new BP28 14-inch (355.6 mm) and BP28L 22.4-inch (569 mm) Line + Gradient Large Diaphragm Condenser Microphones. These microphones... Read more

    Visitor registration opens for ISE 2022

    Visitor registration for ISE 2022 is now open, offering the international AV and systems integration community a long-awaited opportunity to ‘Rise up. Reconnect. Ignite the future’ at its new home in Barcelona, Spain.

    ISE 2022 will reunite the AV industry and provide attendees with the chance to interact and experience world-leading technologies and solutions in person and... Read more
  • Recent articles

    Intelligibility and its measurement

    1. What is intelligibility?

    The state or quality of being understood. It can apply to an idea or a writing, but in our context it relates to the spoken word and, less commonly, to music.... Read more

    Choosing loudspeaker cable

    The importance of cables for the connection between the amplifier and the speaker is often controversial. Hi-fi aficionados spend fortunes on cables that promise spectacular results, and our short auditory memory and subjectivity lead many to confirm these improvements in their systems.... Read more

    Constant voltage systems (70V, 100V lines)

    Constant voltage, high impedance or line transformer systems are often a somewhat confusing concept for professionals used to rock and roll. They are actually very simple to design, among other things because they are intended to be installed by electricians and the like, with little experience in sound systems. In this article we will try to clarify the simple concepts needed to understand this type of system.... Read more
  • PAcalculate app