• Aux fed subwoofers

    There are many types of sound sources that do not require subwoofer reinforcement since they lack low frequency content. For instance, most signals captured by microphones such as voices and instruments in general, except those that do have low frequency content, like double bass or kick drum. Moreover, noises such as stage rumble and handling noise leak into the microphones, as well as sound emanating from the main PA and the stage monitors. It is therefore beneficial to remove the low frequency content on such signals.

    To filter out unwanted low frequencies, the built-in high-pass filter of a mixer's channel is often used (most serious live sound consoles would have this feature). It attenuates frequencies below the cutoff frequency, which is typically in the 75 -100 Hz range, depending on mixer model, although some have it sweepable. The filter slope is commonly 12 dB per octave.

    The slope of this high pass filter may not be steep enough to filter out unwanted bass effectively. Or the cutoff frequency may not be low enough. There are also mixing engineers that wish to add a different amount of subwoofer level to each instrument. In those cases, the subwoofer way is fed through a post-fader auxiliary bus on the mixer. Thus, the channels that have the 'aux' level at zero work in a similar way as if they had the channel high pass filter switched on, except for the fact that the filter characteristics are now those of the electronic cross over, which are typically 24 dB/octave, and a cutoff frequency which is that of the subwoofer way.

    This way of mixing needs an additional cross over channel. These days digital processors have become cost effective and therefore popular, and they often feature a spare input that will be fed by the mixer's aux, so that a single processor can be used to accommodate aux fed subs. However, if we are using a more traditional cross over or controller unit, we will need an extra unit.

    Driving the subwoofers from an auxiliary would normally mean a monophonic subwoofer channel, although there is no reason why two different auxiliaries could be not used to provide a stereo subwoofer channel, other than the fact that it may not provide much of a benefit and would eat up two many mixer auxiliaries and make the arrangement complicated.

    With respect to assigning subwoofer levels on each channel auxiliary bus level, there exist two distinct schools of thought. The first, more technically correct and purist, aims to reflect the same frequency balance that would be achieved without driving the subwoofers separately. We must therefore calibrate the channels' aux levels as well as the main aux controls so that the subwoofer level is the same as if we had driver them in the conventional way.

    The second school of thought would be more liberal, and would assign subwoofer level on each channel subjectively as required by each instrument.

    The illustration below shows the configuration for a 3-way active system with subwoofers fed from an auxiliary mixer bus, compared to a similar system with subwoofers driven conventionally.



    Conventionally fed subwoofers



    Aux fed subwoofers


    NOTE: In general one should always be wary of time alignment between subwoofers and mid-highs. This is even more so in the case of aux-fed subwoofers, since the are signals taking separate paths that may result in different crossovers, EQ or even limiting (if it is digital and specially of the look-ahead type).
  • Ad

  • News

    LEA Professional introduces 6000W Connect Series 1504 power amplifier

    LEA Professional, manufacturer of pro-audio power amplifiers with cloud- and IoT-based technologies, is now shipping its new Connect Series 1504. This new high-power amplifier is a game-changing solution... Read more

    RCF XPS 16k power amp: 4x4000W in 2U


    RCF has now unleashed its power amplification and signal processing technology into a 2U package for mobile touring and installed audio applications. Achieving a new milestone... Read more

    Zenso DMeter meter application for Dante

    Audinate allows for third-party applications for a customized Dante experience, purchases being handled directly by Audinate. One such application is Zenso's DMeter, which provides a view of the levels of Dante... Read more

    JBL VTX A6 line array element and B15 arrayable subwoofer

    JBL Professional has introduced the newest members of its flagship VTX line array series, the VTX A6 subcompact dual 6.5-inch passive line array element and the B15 compact, arrayable 15-inch subwoofer.

    The A6 and B15 reportedly bring JBL’s top acoustic technologies to compact form factors for small- to medium-size touring and fixed installations, providing versatile solutions for production... Read more
  • Recent articles

    Intelligibility and its measurement

    1. What is intelligibility?

    The state or quality of being understood. It can apply to an idea or a writing, but in our context it relates to the spoken word and, less commonly, to music.... Read more

    Choosing loudspeaker cable

    The importance of cables for the connection between the amplifier and the speaker is often controversial. Hi-fi aficionados spend fortunes on cables that promise spectacular results, and our short auditory memory and subjectivity lead many to confirm these improvements in their systems.... Read more

    Constant voltage systems (70V, 100V lines)

    Constant voltage, high impedance or line transformer systems are often a somewhat confusing concept for professionals used to rock and roll. They are actually very simple to design, among other things because they are intended to be installed by electricians and the like, with little experience in sound systems. In this article we will try to clarify the simple concepts needed to understand this type of system.... Read more
  • PAcalculate app