• Aux fed subwoofers

    There are many types of sound sources that do not require subwoofer reinforcement since they lack low frequency content. For instance, most signals captured by microphones such as voices and instruments in general, except those that do have low frequency content, like double bass or kick drum. Moreover, noises such as stage rumble and handling noise leak into the microphones, as well as sound emanating from the main PA and the stage monitors. It is therefore beneficial to remove the low frequency content on such signals.

    To filter out unwanted low frequencies, the built-in high-pass filter of a mixer's channel is often used (most serious live sound consoles would have this feature). It attenuates frequencies below the cutoff frequency, which is typically in the 75 -100 Hz range, depending on mixer model, although some have it sweepable. The filter slope is commonly 12 dB per octave.

    The slope of this high pass filter may not be steep enough to filter out unwanted bass effectively. Or the cutoff frequency may not be low enough. There are also mixing engineers that wish to add a different amount of subwoofer level to each instrument. In those cases, the subwoofer way is fed through a post-fader auxiliary bus on the mixer. Thus, the channels that have the 'aux' level at zero work in a similar way as if they had the channel high pass filter switched on, except for the fact that the filter characteristics are now those of the electronic cross over, which are typically 24 dB/octave, and a cutoff frequency which is that of the subwoofer way.

    This way of mixing needs an additional cross over channel. These days digital processors have become cost effective and therefore popular, and they often feature a spare input that will be fed by the mixer's aux, so that a single processor can be used to accommodate aux fed subs. However, if we are using a more traditional cross over or controller unit, we will need an extra unit.

    Driving the subwoofers from an auxiliary would normally mean a monophonic subwoofer channel, although there is no reason why two different auxiliaries could be not used to provide a stereo subwoofer channel, other than the fact that it may not provide much of a benefit and would eat up two many mixer auxiliaries and make the arrangement complicated.

    With respect to assigning subwoofer levels on each channel auxiliary bus level, there exist two distinct schools of thought. The first, more technically correct and purist, aims to reflect the same frequency balance that would be achieved without driving the subwoofers separately. We must therefore calibrate the channels' aux levels as well as the main aux controls so that the subwoofer level is the same as if we had driver them in the conventional way.

    The second school of thought would be more liberal, and would assign subwoofer level on each channel subjectively as required by each instrument.

    The illustration below shows the configuration for a 3-way active system with subwoofers fed from an auxiliary mixer bus, compared to a similar system with subwoofers driven conventionally.



    Conventionally fed subwoofers



    Aux fed subwoofers


    NOTE: In general one should always be wary of time alignment between subwoofers and mid-highs. This is even more so in the case of aux-fed subwoofers, since the are signals taking separate paths that may result in different crossovers, EQ or even limiting (if it is digital and specially of the look-ahead type).
  • Ad

  • News

    inMusic acquires ArKaos

    Fort Lauderdale, FL USA (October 27, 2020) inMusic, the has announced the acquisition of ArKaos.

    Founded in 1996, ArKaos specializes in video processing technologies,... Read more

    Meyer Sound launches Spacemap Go, a tool for spatial sound design and mixing

    Meyer Sound has officially released Spacemap® Go for spatial sound design and mixing. Available now as a free app for Apple iPad (any iPad capable of running the latest iPadOS), Spacemap... Read more

    Bose unveils L1 Pro family


    These three new portable Bose PA systems are designed to give artists choices, suit different styles and audiences, and provide an solution for creators reintroducing live music and sound experiences into venues and online platforms across... Read more

    ClearOne BMA 360 beamforming microphone array ceiling tile

    ClearOne (NASDAQ:CLRO), provider of audio and visual communication solutions, has announced its new BMA 360, reportedly the world’s most technologically advanced Beamforming Microphone Array Ceiling Tile.

    The ClearOne BMA 360 is the world’s first truly wideband,... Read more
  • Recent articles

    Power amplifier modes : stereo, parallel and bridge mono

    In general, two-channel power amplifiers for professional use default to stereo mode. That is, each amplifier channel receives a signal from its input connector and its volume is controlled by... Read more

    Basic electricity formulas

    Although it not specific to sound, we include this document with some basic electricity formulas. They can be found in any electricity textbook, but we have added them to the DoPA Library for reference.

    Ohm's law

    The most basic formulas derive from Ohm's law, which specifies that the electric current between two points is proportional to the potential difference (voltage) between them and inversely proportional to the resistance between them. The formula is:
    V
    I = ———
    Z


    where I is the current (intensity) in amps and V is the voltage in volts. Since we use alternating current in audio, we have replaced resistance with impedance (Z, and this could also be resistance R), measured in ohms. Clearing Z and V we have these other two formulas:

    V
    Z = ———
    ... Read more

    Y-cables, looping audio signals through

    This article will explain loop-though connections and "y-cables" for analog audio signals.

    To obtain one or more copies of a signal (for example, to distribute the signal from a mixer to various self-powered speakers or power amplifiers) we use parallel connections. To do this we simply connect each terminal (pin) of the connectors in parallel. That is, 1 to 1, 2 to 2 and 3 to 3 (or tip to tip, ring to ring and sleeve to sleeve in a TRS connector). When we split a signal in two in this way, we refer to a "Y-cable" or "Y" connection, since the division of a signal in two looks like letter "y". Contrary to what it may seem, a y-cable is not a technically incorrect solution, but a correct way of splitting the audio signal. In fact, when a self-powered loudspeaker system or one channel of... Read more
  • PAcalculate app