• Aux fed subwoofers

    There are many types of sound sources that do not require subwoofer reinforcement since they lack low frequency content. For instance, most signals captured by microphones such as voices and instruments in general, except those that do have low frequency content, like double bass or kick drum. Moreover, noises such as stage rumble and handling noise leak into the microphones, as well as sound emanating from the main PA and the stage monitors. It is therefore beneficial to remove the low frequency content on such signals.

    To filter out unwanted low frequencies, the built-in high-pass filter of a mixer's channel is often used (most serious live sound consoles would have this feature). It attenuates frequencies below the cutoff frequency, which is typically in the 75 -100 Hz range, depending on mixer model, although some have it sweepable. The filter slope is commonly 12 dB per octave.

    The slope of this high pass filter may not be steep enough to filter out unwanted bass effectively. Or the cutoff frequency may not be low enough. There are also mixing engineers that wish to add a different amount of subwoofer level to each instrument. In those cases, the subwoofer way is fed through a post-fader auxiliary bus on the mixer. Thus, the channels that have the 'aux' level at zero work in a similar way as if they had the channel high pass filter switched on, except for the fact that the filter characteristics are now those of the electronic cross over, which are typically 24 dB/octave, and a cutoff frequency which is that of the subwoofer way.

    This way of mixing needs an additional cross over channel. These days digital processors have become cost effective and therefore popular, and they often feature a spare input that will be fed by the mixer's aux, so that a single processor can be used to accommodate aux fed subs. However, if we are using a more traditional cross over or controller unit, we will need an extra unit.

    Driving the subwoofers from an auxiliary would normally mean a monophonic subwoofer channel, although there is no reason why two different auxiliaries could be not used to provide a stereo subwoofer channel, other than the fact that it may not provide much of a benefit and would eat up two many mixer auxiliaries and make the arrangement complicated.

    With respect to assigning subwoofer levels on each channel auxiliary bus level, there exist two distinct schools of thought. The first, more technically correct and purist, aims to reflect the same frequency balance that would be achieved without driving the subwoofers separately. We must therefore calibrate the channels' aux levels as well as the main aux controls so that the subwoofer level is the same as if we had driver them in the conventional way.

    The second school of thought would be more liberal, and would assign subwoofer level on each channel subjectively as required by each instrument.

    The illustration below shows the configuration for a 3-way active system with subwoofers fed from an auxiliary mixer bus, compared to a similar system with subwoofers driven conventionally.



    Conventionally fed subwoofers



    Aux fed subwoofers


    NOTE: In general one should always be wary of time alignment between subwoofers and mid-highs. This is even more so in the case of aux-fed subwoofers, since the are signals taking separate paths that may result in different crossovers, EQ or even limiting (if it is digital and specially of the look-ahead type).
  • Ad

  • News

    QSC expands Q-SYS Control plugin library with Cisco and Barco meeting room endpoints



    QSC has announced this week the availability of two new Q-SYS™ Control plugins, enabling quick integration and a consistent user experience for the Cisco conferencing... Read more

    DirectOut PRODIGY Series Now Available With Ember+ Network-Based Protocol

    DirectOut's PRODIGY Series of DSP processors was designed to add support of third party control protocols, easing integration into projects where independent or existing... Read more

    PreSonus AVB-D16 brings Dante to StudioLive Series III

    The first plug-and-play endpoint that bridges AVB and Dante networks, the PreSonus AVB-D16 16x16 AVB-to-Dante Bridge enables sending and receiving up to 16 audio channels... Read more

    Waves Audio now shipping the WSG-HY128 Card for Yamaha RIVAGE PM Series

    Waves Audio WSG-HY128 Card for Yamaha RIVAGE PM Series Consoles is now shipping.

    The Waves WSG-HY128 is a card for HY slots that makes it possible to run Waves plugins... Read more
  • Recent articles

    Y-cables, looping audio signals through

    This article will explain loop-though connections and "y-cables" for analog audio signals.

    To obtain one or more copies of a signal (for example, to distribute the signal from a mixer to various self-powered speakers or power amplifiers) we use parallel connections. To do this we simply connect each terminal (pin) of the connectors in parallel. That is, 1 to 1, 2 to 2 and 3 to 3 (or tip to tip, ring to ring and sleeve to sleeve in a TRS connector). When we split a signal in two in this way, we refer to a "Y-cable" or "Y" connection, since the division of a signal in two looks like letter "y". Contrary to what it may seem, a y-cable is not a technically incorrect solution, but a correct way of splitting the audio signal. In fact, when a self-powered loudspeaker system or one channel of... Read more

    Pinouts

    Pin asignments for an assortment of connectors: XLR, 1/4" (jack), 1/8" (minijack), SpeakON, DB25, DMX ...


    ... Read more

    Octaves and third-octaves

    Octaves, thirds of octaves and decades are divisions of the spectrum used in audio, since they work in the same way as the ear, increasing their width in Hertz as frequency increases, and decreasing it when frequency decreases. They are used for the definition of the width of filters, as well as for the spectral analysis.... Read more
  • PAcalculate app