• Aux fed subwoofers

    There are many types of sound sources that do not require subwoofer reinforcement since they lack low frequency content. For instance, most signals captured by microphones such as voices and instruments in general, except those that do have low frequency content, like double bass or kick drum. Moreover, noises such as stage rumble and handling noise leak into the microphones, as well as sound emanating from the main PA and the stage monitors. It is therefore beneficial to remove the low frequency content on such signals.

    To filter out unwanted low frequencies, the built-in high-pass filter of a mixer's channel is often used (most serious live sound consoles would have this feature). It attenuates frequencies below the cutoff frequency, which is typically in the 75 -100 Hz range, depending on mixer model, although some have it sweepable. The filter slope is commonly 12 dB per octave.

    The slope of this high pass filter may not be steep enough to filter out unwanted bass effectively. Or the cutoff frequency may not be low enough. There are also mixing engineers that wish to add a different amount of subwoofer level to each instrument. In those cases, the subwoofer way is fed through a post-fader auxiliary bus on the mixer. Thus, the channels that have the 'aux' level at zero work in a similar way as if they had the channel high pass filter switched on, except for the fact that the filter characteristics are now those of the electronic cross over, which are typically 24 dB/octave, and a cutoff frequency which is that of the subwoofer way.

    This way of mixing needs an additional cross over channel. These days digital processors have become cost effective and therefore popular, and they often feature a spare input that will be fed by the mixer's aux, so that a single processor can be used to accommodate aux fed subs. However, if we are using a more traditional cross over or controller unit, we will need an extra unit.

    Driving the subwoofers from an auxiliary would normally mean a monophonic subwoofer channel, although there is no reason why two different auxiliaries could be not used to provide a stereo subwoofer channel, other than the fact that it may not provide much of a benefit and would eat up two many mixer auxiliaries and make the arrangement complicated.

    With respect to assigning subwoofer levels on each channel auxiliary bus level, there exist two distinct schools of thought. The first, more technically correct and purist, aims to reflect the same frequency balance that would be achieved without driving the subwoofers separately. We must therefore calibrate the channels' aux levels as well as the main aux controls so that the subwoofer level is the same as if we had driver them in the conventional way.

    The second school of thought would be more liberal, and would assign subwoofer level on each channel subjectively as required by each instrument.

    The illustration below shows the configuration for a 3-way active system with subwoofers fed from an auxiliary mixer bus, compared to a similar system with subwoofers driven conventionally.



    Conventionally fed subwoofers



    Aux fed subwoofers


    NOTE: In general one should always be wary of time alignment between subwoofers and mid-highs. This is even more so in the case of aux-fed subwoofers, since the are signals taking separate paths that may result in different crossovers, EQ or even limiting (if it is digital and specially of the look-ahead type).
  • Ad

  • News

    Powersoft supports the Crew Nation fund


    Live music inspires millions around the world, but while artists have been able to embrace the new possibilities afforded by social media and streaming sites in the wake of Covid-19, the talented men and... Read more

    Shure introduces SLX-D digital wireless system

    The SLX-D Digital Wireless System is the newest addition to the Shure digital wireless portfolio. The new offering is the digital replacement of the company’s SLX system,... Read more

    dBTechnologies VIO L1610 3-way line-array system



    Italian pro audio manufacturer dBTechnologies has launched a new member of the VIO family: a compact 3-way active line array system equipped with 2x10” woofers and 1 coaxial MF/LF compression driver.

    VIO L1610 is a three-way active line-array system, entirely equipped with neodymium components:... Read more

    ID14, the smallest loudspeaker in Nexo's history

    Despite constraining regulations on its production processes, NEXO has just unveiled a new point source speaker. The smallest loudspeaker design in the company’s 40-year history, the new ID14, and its S108 partner... Read more

    Categorías:

    Cajas acústicas 
  • Recent articles

    Parallel and series connections: description and calculations

    In this article we'll explain impedance calculations as simply as possible, as well as describe the different types of connection.... Read more

    Loudspeaker impedance

    Measured in ohms (symbol, Ω, upper case Greek letter omega), electrical impedance is defined as the opposition to the flow of alternating current by means of presenting an electrical load. In a loudspeaker, impedance varies with frequency, so manufacturers often publish "impedance curves" showing impedance with frequency for passive units. These curves give us... Read more

    Balanced and unbalanced connections

    There are two basic ways to carry an electrical audio signal.


    • The first one is unbalanced. The signal is carried on a two-conductor cable. Unbalanced signal connectors have two pins, such as the RCA (also called Phono and Cinch, commonly used by home hi-fi equipment) and the unbalanced 1/4" (used in musical instruments and semi-professional audio). Multi-pin connectors can also carry
    ... Read more
  • PAcalculate app