• Dynamics Processors : Noise gates (expanders)

    In this article we'll go through noise gate control and how to use them in different applications. If you haven't already, do read Introduction to dynamics processors first.

    The aim of a pure noise gate is to mute signals with low volume. Most gates are also able to close just partially, providing a set attenuation as opposed to muting the signal completely.

    There exist several reasons why a noise gate may be needed. For recording applications, gates are used to eliminate background noise when the instrument or voice is not generating a signal (during pauses, and just before the song starts and after the song has just finished). For sound reinforcement applications gates are not as necessary since background noise is not such a big problem once the show is taking place, so gates tend to be used more with the idea of avoiding other sounds from leaking into a microphone that is not being used. The most sophisticated drum micing might use gates to avoid picking up the sound of other drums with the microphone that is supposed to pick up just the sound of a specific drum. For instance, the bass drum mic would only be active during bass drum hits, while the snare drum gate would only be open for snare hits, such that the snare does not leak into the bass drum microphone, and vice versa.

    Typically, gating takes place in a slower way compared to compression (and modifies only signal RMS levels). Also, gates are often closed for a relatively long time. Like for compressors, the detection circuit is extremely important, and may vary widely from model to model.

    Also, it is important to understand that gates do not eliminate the noise. They just hide it by attenuating it when it is most obvious (during pauses), and let it through when it is mixed with the signal.

    1. Controls

    Gating is a difficult task that may require very different characteristics depending of the type of signal. Numerous controls are therefore needed. The drawing below shows a noise gate (downward expander) with the most common controls.

    The most common controls provided on gates are given below. You may not always find all of them, or you may get additional ones.

    • Threshold. When the signal falls below the threshold level the dynamic processing starts and the gate begins to close. In general, this control needs to be adjusted as low as possible (without false gate openings), since that way the original signal will be preserved.
    • Attack time. This is the time it takes for the gate to fully open once the signal exceeds the threshold level. Lowest available attack times would be in the 10-100 us (microsecond) range depending on the unit, while maximum attack times vary considerably depending on manufacturer and model, but would go anywhere from 200 ms (milliseconds) to 1 second. Fast times may create distortion artifacts, as they modify the waveform of low frequencies, which are slow. For example, a 100 Hz cycle lasts 10 ms, so that an attack time of 1 ms has the time to modify the wave form and generate distortion. On the other hand, a time that is too long will remove the percussive transient from a drum sound. In general, it should be as fast as possible, but not too fast to cause clicks or distort the attack of a signal.
    • Hold time. This is the time that the gate is kept open after the signal level has fallen below the threshold, and is therefore the minimum time that the gate will remain open. It is used to prevent altering the decay of sounds by avoiding short low signal levels triggering the start of the release phase. It can typically be adjusted between zero and several seconds. Sometimes an indicator is provided that lights up during the hold phase. The graph below shows how the different times come into play on a noise gate.

    • Release time, sometimes referred to as decay time. It is the opposite of attack time, i.e. the time it takes to go from the unprocessed state (no attenuation) to the fully processed state where the signal is attenuated or muted. The release times available on a unit are a lot slower than attack times and may range from 2-10 ms to 3-5 seconds. The illustration shows the difference between gating with a slower (left) or faster (right) release time.

    • Hold time. This is the time that the gate is kept open after the signal level has fallen below the threshold, and is therefore the minimum time that the gate will remain open. It is used to prevent altering the decay of sounds by avoiding short low signal levels triggering the start of the release phase. It can typically be adjusted between zero and several seconds. Sometimes an indicator is provided that lights up during the hold phase. The graph below shows how the different times come into play on a noise gate

    • Range or attenuation ratio. Simpler gates just shut down the output completely, though a dedicated gate would normally provide control over the amount of attenuation provided to signals below the threshold level, letting an amount of signal through. One advantage of just providing some degree of attenuation as opposed to muting the signal completely is that when the gate opens, it will do so more smoothly, since the signal does not have to rise from zero. The level reduction can be performed with two different families of devices.
      • Noise gate. It provides a pre-defined attenuation, be it total muting or an intermediate level, which is known as "range", or, sometimes "depth". For instance, we could attenuate 20 dB or 40 dB, or just close the gate completely (-infinity attenuation).
      • Downward expander. This type of unit works like the opposite of a compressor, and provides a "ratio" control or attenuation slope. That way the signal is attenuated more highly the lower the signal level is. In fact, if the threshold is set high enough, we could "expand" the dynamics of the signal, increasing its dynamic range, though this is not normally done. The attenuation ratio works in an equivalent way to that of the compressor, defining the amount of a attenuation (compression) that is applied to the signal. These ratios are expressed in dB, so that, for example, 1:6, means a signal that is 1 dB below the threshold will get reduced to 6 dB below it, while a signal 3 dB below the threshold will get reduced to 18 dB below it. Likewise, a 1:3 (one to three) means a signal 1 dB below the threshold will be attenuated 2 dB (as the level will go from -1 dB to -3 dB; we use a negative sign as these levels are below the threshold, which is the 0 dB reference in this case). With a ratio of 1:10 and higher, the expander is considered to work as a pure noise gate, though an ideal gate would have a theoretical ratio of 1:infinity (any level below the threshold would be totally muted).

      In practice, expanders are used in a very similar way to pure noise gates, with the only difference that downward expansion is smoother and more gradual, and it is therefore more difficult to get the attack and release times wrong. Some units provide the possibility of choosing between gate or expander action. The illustration below shows the difference between a expander with a variety of ratios and a gate with different attenuation "ranges" (depths). If you are having a hard time understanding the input/output graph, do have a look at the compression tutorial.

    • Stereo link. When dynamics processors in general are used to process a stereo signal, it is necessary to synchronize the processing action on the channels so it happens at the same time on both. Otherwise the stereo image will be confusing and move from the center to one side or the other. Mono units often provide a connector that allows linking of two units.
    • Automatic. It is becoming more and more common for equipment to provide the possibility of controlling some of the parameters (normally attack and release times) automatically as a function of the signal characteristics. In general, the automatic mode works well when a transparent subtle effect is looked for.
    • Side chain listen. Noise gates that provide a side chain (explained later) often allow routing of the side chain signal to the main output so that it can be listened to, thus making the setting of the gate easier.
    • Bypass. For comparison of the original and processed signals.
      Dynamic filter. Some gates are equipped with a dynamic filter whose job is to gradually add more high frecuency attenuation as the signal goes down in level. This provides more natural gating action, as instrument and vocal sounds tend to show less harmonics as the instrument is played more softly or the voice is lowered.

    2. Indicators

    • Gating indicator. There is normally a LED indicator that shows whether the gate is open or closed. Normally, the operator also gets some kind of indication of whether the threshold level has been crossed and the release phase is finished.

    3. The side chain

    Normally, the detection circuit uses a copy of the signal being gated to check whether it exceeds the threshold level or not. However, many noise gates allow using an external signal that is fed to the detector via the Side Chain (sometimes also called key) input. That way it is the external signal that triggers the compression, though it is the main signal that gets compressed. There may be a switch that toggles the detection signal between the main and the side chain signal, or sometimes, if the side chain input uses a 1/4" connector (often wrongly referred to as jack in many non-English speaking countries!), it is the connector that enables the function when the 1/4" plug is inserted. This 1/4" jack is an insert type connector that carries both a send and a return signal, the send carrying a copy of the main signal to facilitate its connection to a processor (e.g., an equalizer) and then feeding it back to the detector through the return part of the side chain connector.

    An equalizer is commonly used for the side chain; in fact, some noise gates come equipped with built-in EQ facilities. We could, for instance, attenuate the high frequencies on the detection circuit to avoid the cymbals triggering the noise gate for the bass drum.

  • Ad

  • News

    ClearOne BMA 360 beamforming microphone array ceiling tile

    ClearOne (NASDAQ:CLRO), provider of audio and visual communication solutions, has announced its new BMA 360, reportedly the world’s most technologically advanced Beamforming Microphone Array Ceiling Tile.

    The ClearOne BMA 360 is the world’s first truly wideband,... Read more

    JBL IRX115S 15-Inch Powered Subwoofer

    JBL has introduced the JBL IRX115S powered subwoofer weighing 65.3 pounds.

    With our IRX Series, we’ve drawn from 70 years of JBL innovation to design a portable P.A. that’s lightweight, powerful and doesn’t... Read more

    QSC Adds Q-SYS Processing Capabilities to the NV-32-H Network Video Endpoint

    QSC announces the release of the multipurpose NV-32-H (Core Capable) native network video endpoint for the Q-SYS Ecosystem, which now allows you to toggle between ‘Core Mode,’ which transforms... Read more

    Shure introduces DuraPlex subminiature microphone

    Shure yesterday unveiled DuraPlex, the company’s new subminiature (5 mm) omnidirectional lavalier and headset microphone boasting Shure’s first IP57 certification rating, keeping dirt, dust, water, and perspiration... Read more
  • Recent articles

    Power amplifier modes : stereo, parallel and bridge mono

    In general, two-channel power amplifiers for professional use default to stereo mode. That is, each amplifier channel receives a signal from its input connector and its volume is controlled by... Read more

    Basic electricity formulas

    Although it not specific to sound, we include this document with some basic electricity formulas. They can be found in any electricity textbook, but we have added them to the DoPA Library for reference.

    Ohm's law

    The most basic formulas derive from Ohm's law, which specifies that the electric current between two points is proportional to the potential difference (voltage) between them and inversely proportional to the resistance between them. The formula is:
    I = ———

    where I is the current (intensity) in amps and V is the voltage in volts. Since we use alternating current in audio, we have replaced resistance with impedance (Z, and this could also be resistance R), measured in ohms. Clearing Z and V we have these other two formulas:

    Z = ———
    ... Read more

    Y-cables, looping audio signals through

    This article will explain loop-though connections and "y-cables" for analog audio signals.

    To obtain one or more copies of a signal (for example, to distribute the signal from a mixer to various self-powered speakers or power amplifiers) we use parallel connections. To do this we simply connect each terminal (pin) of the connectors in parallel. That is, 1 to 1, 2 to 2 and 3 to 3 (or tip to tip, ring to ring and sleeve to sleeve in a TRS connector). When we split a signal in two in this way, we refer to a "Y-cable" or "Y" connection, since the division of a signal in two looks like letter "y". Contrary to what it may seem, a y-cable is not a technically incorrect solution, but a correct way of splitting the audio signal. In fact, when a self-powered loudspeaker system or one channel of... Read more
  • PAcalculate app