• Power amplifier modes : stereo, parallel and bridge mono

    In general, two-channel power amplifiers for professional use default to stereo mode. That is, each amplifier channel receives a signal from its input connector and its volume is controlled by that channel's volume control. So, really, although the name of that default mode is 'stereo', it is more of a two-channel mode, since those two channels do not necessarily have to be right and left. For example, they could be two separate channels for the stage monitors of different musicians. Or the high and midrange bands of a multi-amp system.

    Both channels are often required to carry the same signal. We achieve this by connecting the inputs of the channels in parallel. To do this we can make a so called "Y-cable" with which we exit the signal source (e.g. a mixer) and reach the two input channels. Another way to achieve the same result is, if the amplifier has more than one signal connector, to take the input signal from one channel to the other channel using a short cable that comes out of an unused input connector on one channel and goes into a connector on the other. It is common for amplifier manufacturers to simplify our lives and avoid the complication of the Y-cable or the short loop-through cable. So they provide a switch that activates the parallel mode that simply links the inputs of the two channels of the amplifier so that they carry the same signal. Normally, when selecting the parallel mode, the amplifier takes the signal from channel 1 and the input to channel 2 is disconnected (or should not be used). Depending on the amplifier model, each channel will still maintain its volume control, else channel 1 will control the signal level going to both amplifier channels.
    NOTE: Some amplifiers brands such as Crown/Amcron and Camco have traditionally deployed a parallel mono mode that is totally different from the one described, since the output connections are also paralleled. The manual of our amplifier will give us details and connections for the parallel mode.

    Something similar happens if you want to use an amplifier in bridge mode, i.e. combining the two channels of the amplifier into a single, more powerful, channel (hence the name "bridge mono"). To do this we need to bring the same signal to both channels, except that channel 2 should have the opposite polarity to channel 1. The loudspeaker signal will then come out of the two positive output terminals. To avoid the complication with the wiring, just like with the parallel mode, many amplifiers that allow for bridged use (not all of them do!) provide a bridge mode switch that conveniently makes the required connections internally for us. Depending on the amplifier model, each channel will still maintain its volume control, so we should always use the amplifier with the two volume controls at maximum. Else, channel 1 will control the signal level going to the amplifiers of both channels, so we can use the volume control of channel 1 as the level control of what is now a single amplifier. Please consult your amplifier's manual for details and connections for the bridge mode of your particular model.

    Since the output voltage is doubled, a conventional amplifier will try to deliver four times more power (in theory, in practice it would be slightly less, of the order of only three times more) than in stereo mode per channel (that's around 5 to 6 dB more), so it is common for the minimum allowable impedance for the amplifier in bridge mode to be higher (typically twice) than in stereo mode. For example, a conventional amplifier that delivers 1000W per channel into 4 ohms that connected to a single 4-ohm load in bridge mode will attempt to deliver 4000W (in practice more like 3000W), which would exceed the power capacity of the amplifier, so the manufacturer may specify that the amplifier should only go down to 8 ohms in bridge mode. Similarly an amplifier that goes down to 2 ohms in stereo mode would only go down to 4 ohms in bridge mode. More modern and sophisticated amplifiers may be less restrictive on this.

    In any case, it should be noted that these mode switches that provide many amplifiers are only a convenient way of doing the same thing that we could do with input wiring. Also, muti-channel amplifiers will offer one mode switch for every pair of channels (e.g., and 8-channel amp may have four of these switches).


  • Ad

  • News

    Over 700 exhibitors confirmed for ISE 2022

    Integrated Systems Events informs that over 700 exhibitors already committed to ISE 2022, including bellwether brands Barco, Crestron, KNX, Kramer, LG, Panasonic, Samsung, and Sony – the show floor has been redesigned and will also feature... Read more

    JBL Professional introduces EON700 Series portable PA loudspeakers with Bluetooth


    JBL Professional yesterday introduced the EON700 Series portable PA loudspeakers and subwoofer with Bluetooth.

    With four models available, including the 10-inch EON710, the 12-inch EON712 and the 15-inch EON715 powered PA speakers and... Read more

    Biamp Launches Parlé audio and video conferencing bars

    Biamp, supplier of professional audiovisual solutions, has announced the launch of Parlé™ audio and video conferencing bars, a line of professional grade audiovisual conferencing solutions for... Read more

    Studio Technologies now shipping StudioComm system

    Studio Technologies, manufacturer of audio, video, and fiber-optic solutions, is now shipping the StudioComm System with Dante® Support, consisting of the Model... Read more
  • Recent articles

    Intelligibility and its measurement

    1. What is intelligibility?

    The state or quality of being understood. It can apply to an idea or a writing, but in our context it relates to the spoken word and, less commonly, to music.... Read more

    Choosing loudspeaker cable

    The importance of cables for the connection between the amplifier and the speaker is often controversial. Hi-fi aficionados spend fortunes on cables that promise spectacular results, and our short auditory memory and subjectivity lead many to confirm these improvements in their systems.... Read more

    Constant voltage systems (70V, 100V lines)

    Constant voltage, high impedance or line transformer systems are often a somewhat confusing concept for professionals used to rock and roll. They are actually very simple to design, among other things because they are intended to be installed by electricians and the like, with little experience in sound systems. In this article we will try to clarify the simple concepts needed to understand this type of system.... Read more
  • PAcalculate app